Posté le 30/06/2014 at 22:41

Kitty Injection : Engine : 1776 part. 2

Here's an article that took its sweet time before publishing... Anyway, things are going forward - slowly, but still forward!


I kept working on the case :
  • All edges are smoothed,
  • Casting marks are removed,
  • The ventilation holes between cylinders 1&2 / 3&4 are widened (the three fingers rule!) and smoothed,
  • the oil return hole at the bottom of the partition with the distribution gears is enlarged,
  • the ventilation above the central bearing is enlarged.
It may not look like much, but there's already quite a few hours of Dremel-ing to get there!

The global idea is twofold : first, enhance the air flow inside the crankcase to avoid over-pressure, second, ease the return of the oil to the bottom of the case, in order for it to go back in the oil circuit (the oil remaining on the inner faces of the case is useless!).
Smoothing the edges also helps preventing concentration of constraints in the material, and the cracks that could result from them. Well, to be honest, I'm not really too concerned about that on my little 1776! icone smiley laugh

As a comparison, here is one of the ventilation ports before smoothing... icone smiley wink
As per the tools I use, it's first a pneumatic grinder with carbide bits to quickly remove material, then Dremel and its accessories (sanding cylinder, miscellaneous grinding stones...) to refine, and finally 120/180 grit sand paper for a final smoothing.
For the case's exterior finish, I used a fine rotary abrasive brush (on the pneumatic grinder, this baby gotta turn fast!). The objective was just to remove the oxidization and remaining muck after its previouss chemical cleansing...

Berg Conversion

I had my mind set onto using head washers an nuts around the case ("Gary Berg conversion") : the thick washers (4mm) and the 15mm nuts allow a tighter torquing of the case perimeter (2.7mkg instead of the origin 2mkg), leading to a more rigid crankcase.
But to do so, one needs first to spot face the case for the washers to lay flat on the material... As I did not really want to go ask pay a professional machinist to make that modification, and since I'm kinda stubborn (icone smiley laugh), I found a way to make it myself.
In order to do so, you would first need the right tool, a 22mm counterboring bit with a 8mm pilot tip (actually fellow enthousiast KY260, advised that Ø23mm is even better, as the washer may be a bit tight with 22mm). Not an easy to find tool, but I finally found it on eBay : a set of 23mm cutters, with two CM3 tool holders and 4 14.4mm pilot tips. At 44€, that was a steal! icone smiley wink
As I don't have a mill, I want to use that tool with my drill press ; in order to do so, I lathed down one of the CM3 tool holders to give it a cylindrical end instead of the conical morse one. I also lathed one of the pilot tips down to 8.5mm (that hardened steel was very, very hard to lathe!).
Finally, I have the correct tooling, let's give it a shot!
Before I actually modify my crankcase, I did make a few tests on my former, out-of-tolerances case, just to validate the process first. Finally, I found a way to do it, by clamping my drill press down on the bench, turning the drill press head backwards to get enough height, and drilling slowly... I know my assembly will make any proper machinist shiver, but the resulting spot faced areas are really nice and flat and perpendicular : process validity checked! icone smiley wink

So, here we go now, same procedure on my actual case. It's actually quite a quick process, except the ones below the case ; some Dremel work was required to free the way for the cutter.

Unpluging the oil galleries

In order to thoroughly clean the oil galleries, and by doing so avoid that some gunk would screw up all the nice work do so far upon engine's first start, you must un-plug the galleries. The operation isn't that difficult if you're careful : first center-punch the plug, then drill it with a 3mm drill bit ; then force-screw a sheet metal screw in that hole, and pull on it with an inertia hammer.
Since I did not have an actual inertia hammer, I thew one together with what was available around the workbench... I'm actually pretty happy of that recycling of an old rear-drum 36mm nut. icone smiley laugh
If you give this modification a shot, here are the plugs you'll need to pull (circled in blue) ; there are 10 of them, but I'll pug back only 9, the last one being the full-flow input.
The plug on the side of the case (right below and between the cylinders 3 and 4) is drilled to a 8.5mm diameter, all the way down (around 67mm, down to right behind the central camshaft bearing), to enhance the oil flow in the right half of the case. With a sharp drill bit, turning fast, going in slowly as to keep the bit from "screwing" into the material, that's quite an easy thing to do (back up often to get the shavings out).

Cleaning and plugging back the galleries

So, now that the galleries are un-plugged, it's time to clean them, and find a way to plug them back after!

Here's the tools of the trade for these two steps...
I ordered plugs from (great address I already got fuel fittings from). These are conical NPT 1/8"x27, 1/4"x18 and 3/8"x18. They are anodized aluminium, really nice products ; to be installed with Loctite 577 pipe sealant ; make sure you have the imperial size Allen wrenches to tighten them in!

As for the cleaning of the galleries, any means are good. Myself, I'm first using the compressed air to get rid of as much shavings and dust as possible ; then bottle brushes, shotgun brushes and pipe-cleaning brushes... And lots of brake cleaning fluid ; some WD40 can be used too, to help removing any hardened oil sticking in the nooks and crannies.
To make it a bit easier, I like to mount the bottle/riffle brushes on my cordless electric drill, and then go back and forth in the galleries while turning full speed ; that's the way to go, galleries end up all nice and shiny! (sorry, no picture about it, I could not manage to get a proper picture inside the oil gallery)
Next, taping the plugs holes... This operation produces a lot of shavings and dust, so make sure you wait till you've finish this step before actually doing your final cleaning of the galleries!

Prior to taping, you first need to drill the holes : here are the drill bits sizes you'll need for that :
  • 1/8" plug : 8,5mm drill bit (11/32"), going 15 mm deep
  • 1/4" plug : 11mm drill bit (7/16" ), going 26 mm deep
  • 3/8" plug : 14,5mm drill bit (37/64" or 9/16"), going 25 mm deep
Drilling depths are just given as an indication ; they totally depend on your taps and plugs, so don't take my word for it and make your own trials! icone smiley wink

You need to be cautious while taping, as it's conical. As per the depth, you need to go little by little : tap a little, test fit the plug, tap a bit more, test fit the plug, et cætera until the plug sits flush with the case when tighten. To make it easier/faster, once the first plug of a given size is tapped, I make a mark on the tap for the next ones! (see previous picture, red marker stripe on the tap)
The gallery on the output side of the oil pump needs to be plugged as well. The pump itself is already tapped, but plugging the gallery too will prevent oil pressure from coming back in this gallery, causing leaks and/or oil going back in the case instead of the circuit. I put that plug deep into the gallery, that should help avoiding gunk and debris from stocking up in that dead-end part of the oil circuit.
So here we go gain, NPT 1/4"x18 tap, directly in the gallery without any prior drilling (inside diameter is correct). Half a turn ahead, quarter turn back to get shavings ou, and repeat... The plug will be tightened in the gallery with its dose of Loctite 577 pipe sealant again.


Out of the box, the cams edges are razor sharp, which may damage the lifters upon engine's first start. So I lightly smooth them down with my Dremel and a sanding drum. It doesn't need much, just smoothing down that angle a bit ; I finish it off with some 600 grit sandpaper with a drop of oil.
The journals are polished with some 2000 grit sand paper (a worn-out ScotchBrite pad would work too), to remove any imperfection and promote the oil film. If you use sand paper though, make sure you thoroughly clean the part after, as grit particles may get embedded in the material (well, that's more true about the soft material of bearings han the hard steel of the journals!).
Assembling the driving gear : the screws delivered with the camshaft have a ring protruding on top of them, which may interfere with the back of the oil pump. Since that ring does not bring anything in terms of resistance to the screws, I lathe it down (well, a file would have done the trick too!).
Finally, a thorough cleaning/degreasing of all the parts (brakes cleaning fluid, acetone), and assembly, torquing the screws at 25nm, with a drop of Loctite threadlock (the stronger, red one - you really don't want these to get loose!). The notch in the camshaft (that drives the oil pump) has to be aligned with the mark on the gear.
I give the whole thing a thin coat of WD40 to prevent any oxidization, and I put it aside, in a clean protective plastic bag.

Oil pump

The oil pump is a modified model, prepped by Feller Service (a french perf shop) : it's a Shadek 26mm base, machined to add a couple of O-rings around it (to prevent leaks and cavitation). The pump body and gears are rectified so that the gears are perfectly flush with the body (checked with my trustful rectified ruler).
The output is already plugged, with the full-flow output on the anodized black, CNC aluminium cover (tastefully engraved with the name of my fav parts dealer! icone smiley laugh).
More information about this pump on Feller's blog (in french only I'm afraid) ; actually if you give it a close look, my pump cover is somewhere on the last picture, on the right hand side... icone smiley laugh
Anyway, here's a really nice, highly recommended product, and made in France for once!
Still, I make a couple of modifications on it : first, the tear drop shaped input as recommended by Berg, so that the oil arrives nicely all along the gear. I also slightly grind down the rear protruding tenon, to make sure it won't interfere with the camshaft screws.
The oil inlet port is aligned with the gallery on the case (see this post by PanelVan) ; I was luck, I had less than half a millimeter gap, so a light Dremel sanding drum touch in the pump body was enough to align it perfectly.
And that's it, enough for the oil pump, it's ready to install!

To be continued soon!
Posté dans : 1968 Karmann Ghia
Affiché 126038 fois.
icon permalink
© Sham 1996-2019